{"product_id":"phrozen-dental-wash-and-v-cure-bundle","title":"Phrozen Dental Wash+ and V-CURE Bundle","description":"\u003ch2\u003ePhrozen Dental Wash+ and V-CURE Bundle: Washing and Vacuum Curing for Dental 3D Printing\u003c\/h2\u003e\n\u003cp\u003eThe Phrozen Dental Wash+ and V-CURE Bundle pairs the Phrozen Wash+ dual tank washing station with the Phrozen V-CURE vacuum curing station, for dental clinics and laboratories in Australia that print occlusal splints, surgical guides, temporaries, crowns, bridges and dentures. Buying both units as a bundle covers the washing and post curing stages in a single order.\u003c\/p\u003e\n\u003ch3\u003eWash+ washing station\u003c\/h3\u003e\n\u003cp\u003eThe Wash+ cleans printed parts in IPA using a dual tank system that supports three washing methods: a two stage wash for thorough resin removal, separation of biocompatible and non-biocompatible parts, or loading both tanks at once to clean up to 24 dental models. Cycles take approximately five minutes, with five speed levels from 250 to 350 RPM in 25 RPM steps, and the touchscreen stores up to 200 washing profiles. The included Small Bucket Set limits solvent to a maximum of 4 litres per tank, and the stainless steel plate holder fits all Phrozen Dental Series build plates without adapters.\u003c\/p\u003e\n\u003ch3\u003eV-CURE vacuum curing station\u003c\/h3\u003e\n\u003cp\u003eThe V-CURE pulls the chamber down to a vacuum before UV curing starts. This removes the oxygen that otherwise leaves a tacky, under cured surface on resin parts, so there is no glycerine bath and no external nitrogen supply. It cures with 36 LEDs at 365, 385 and 405nm, up to 130 W, with a maximum vacuum rating of 720 mmHg and a 120 x 120 x 50 mm curing volume. Phrozen's estimated cycles are 3 to 4 minutes for surgical guides, 6 minutes for occlusal splints, crowns and bridges, and 7 minutes for dental models. Profiles are selected on the 5 inch touchscreen, with 5 levels of UV intensity and 4 levels of Flash mode. The V-CURE has no heater.\u003c\/p\u003e\n\u003ch3\u003eHow the two units work together\u003c\/h3\u003e\n\u003cp\u003eWash printed parts in the Wash+, dry them completely, then move them to the V-CURE. Parts must be free from uncured resin and fully dry before they go into the vacuum chamber. Standard UV curing is usually enough for dental models, so the V-CURE earns its place on splints, guides, temporaries, crowns, bridges and dentures, where surface cure and material performance matter most. Check that your parts fit the 120 x 120 x 50 mm curing volume before ordering.\u003c\/p\u003e\n\u003cp\u003e3D Cast is Australia's official Phrozen distributor, with technical support for both units handled locally.\u003c\/p\u003e","brand":"Phrozen","offers":[{"title":"Default Title","offer_id":48097213939889,"sku":"PHWVC01","price":5100.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0669\/1569\/6817\/files\/Phrozen-Dental-Wash_-and-V-CURE-Bundle-Phrozen-139164042.jpg?v=1793053915","url":"https:\/\/3dcaststore.com.au\/products\/phrozen-dental-wash-and-v-cure-bundle","provider":"3D Cast","version":"1.0","type":"link"}