Monocure3D RinseOFF - Your Essential 3D Printing Accessory
Monocure3D RinseOFF - Your Essential 3D Printing Accessory is backordered and will ship as soon as it is back in stock.
Delivery and Shipping
Delivery and Shipping
Product Care
Product Care
Returns
Returns
Monocure3D RinseOFF - Your Essential 3D Printing Accessory
Monocure3D RinseOFF: Final Rinse Solution for Resin 3D Prints
Monocure3D RinseOFF is a final rinse solution designed for use after the primary Resinaway wash step in the resin 3D print post-processing workflow. Its function is to remove any residual Resinaway or oily film that remains on the print surface after the wash stage, producing a clean, dry surface that is ready for UV post-curing without residue interference.
The reason a second rinse step exists is chemical. Resinaway and similar wash solvents dissolve uncured resin from the print surface, but a thin film of the solvent itself can remain on the print after the wash. If this film is not removed before UV curing, it inhibits full surface cure and leaves a slightly tacky or cloudy layer. RinseOFF is formulated specifically to displace that residual film without itself leaving a residue, producing a surface that cures cleanly and completely under UV exposure.
RinseOFF is non-flammable and low-odour, consistent with the Monocure3D philosophy of reducing the flammability and ventilation risks in the post-processing workflow. Its low evaporation rate means the solution lasts across a high number of rinse cycles before requiring replacement. It is compatible with ultrasonic cleaners, dedicated wash stations, and manual rinse containers, and works with all MSLA and DLP resin types.
3D Cast is Australia's official Monocure3D distributor, stocking genuine RinseOFF with fast shipping Australia wide.
Why the Mini 8KS
-
01Eliminates Tackiness
Removes the thin resin oil film that survives primary washing and UV curing, leaving the surface dry to the touch and chemically clean.
-
02Paint-Ready Surface
Paint beading and adhesion failure are caused by microscopic resin oils on the surface. RinseOFF removes that contamination before primer is applied.
-
03No Water Rinse
Unlike water-based secondary wash methods, RinseOFF leaves prints ready to cure immediately after air drying. No additional rinse or drying step required.
-
045 min
typical soak time
NO MORE STICKY 3D PRINTS
Learn why resin prints stay tacky after curing and how a two-stage wash with RinseOFF solves the problem permanently.
Complete your post-processing setup
Product Specifications
Technical specifications for Monocure3D RinseOFF.
Product Specifications
Technical specifications for Monocure3D RinseOFF.
3D Cast is the official Australian distributor for Monocure3D, stocking the full Monocure3D range including ResinAway and RinseOFF from our Bairnsdale, Victoria warehouse. All products are genuine Monocure3D inventory. Technical support is available directly from our team.
Frequently Asked Questions
Tackiness after UV curing is caused by a thin layer of uncured resin oil that was not fully removed during the primary wash, or by oxygen inhibition preventing the outer surface from polymerising completely. RinseOFF removes that residual oil layer, leaving the surface dry and fully ready for curing.
RinseOFF is designed as a second-stage wash, not a primary wash. Use ResinAway or IPA first to remove the bulk of the liquid resin, then use RinseOFF as the final polish wash. This keeps the RinseOFF solution cleaner for longer and gives the best surface result.
No. RinseOFF leaves prints ready for UV curing once dry. Air dry or use compressed air after the soak, then move directly to the UV station. No water rinse is needed.
Five minutes is sufficient for most hobby and mid-size prints. For large or complex parts with internal cavities, the soak can be extended slightly, but RinseOFF is efficient enough that extended soak times are rarely necessary.
Yes. RinseOFF is formulated to work with standard photopolymer resins, tough resins, water-washable resins, and specialty casting resins. It is gentle on the cured plastic while removing the sticky residue.
Yes. Paint beading, peeling, and poor primer adhesion are caused by microscopic resin oils remaining on the surface after washing. RinseOFF removes that contamination and creates a clean surface for primer and paint to bond to without additional sanding.
ResinAway is a primary wash solution that replaces IPA for removing bulk liquid resin from prints after removal from the build plate. RinseOFF is a secondary polish wash that removes the final sticky resin film after the primary wash is complete. The two products are used in sequence, not as alternatives.
Yes. RinseOFF is stocked by 3D Cast, the official Australian distributor for Monocure3D, and ships from our Bairnsdale, Victoria warehouse via Australia Post.
Let customers speak for us
Cannot praise the service enough. The order was dispatched the same day as ordered and promptly received. All queries since the order have been responded to in a very timely manner.
Have printed four lots of dental arches with this resin and have had successful prints each time with no problems. Cheaper than the previous high temp resin I was using and more successful print quality so far. Would buy again.
Works perfectly as advertised. Easy to install, even with fat fingers. Good price, excellent service as always from the team at 3Dcast. Thank you.
Easy to communicate with and order fulfillment was prompt. I’ll be back!!
Really user friendly - easy to work with (even in very small quantities and very tight spots). Cures almost instantaneously under the supplied UV torch and then easy to sand back, scribe etc. A must have product for scale modeling!
Delivered super fast, product works as described. Very happy
Delivered super fast, product works as described. Very happy
service and delivery is very quick and efficient.
My husband was so happy with it thank you again.
And youare so helpful with any questions
I’ve tested plenty of resins in the past, but Resione Tough74 v2 is on a completely different level. The material properties are incredible - it’s the perfect balance of rigidity and toughness. I’m using it for articulated garage resin kits, and the results are flawless. If you are tired of brittle prints and want something that actually feels like a manufactured product, this is it!
I have used the Phrozen 8K resin before, so I know how good a product it is. Delivery was fast. Sadly, whoever delivered it left it in the foyer of my apartment building without even buzzing me. Nothing to do with 3D cast but I hate to think what would have happened if a kid had got their hands on it.
Simple replacement part. Easy install. Comes with replacement tape included. Good product.
Ready to order?
3D Cast is Australia's official Monocure3D distributor. In stock, fast dispatch, local support.
Back to top — Add to Cart